.bmp)
If you are in the process of starting a jewel line, there is a need to know how they are created so that you meet customer demands more effectively. Several methods are involved in making the final products. As long as the methods adhere to unique products are created, and this is what will bring customers to your shop. Below are steps involved in Tufa casting custom jewelry NM.
Stone preparation is the first step for those involved in this process. One has to find the right size of stone that fits the description of the designs they have in mind. After the proper size has been found, it is essential the two sides are flattened and left in a smooth state. The two sides need to be perfectly flat and identical to each other.
With stones ready, sketching the designs of models that one had thought of begins. Here one ought to be keen and do the job in a quiet environment to avoid disturbances which might result in errors. Also, a lot of time needs to be put when making the sketches.
Use the necessary design tools to carve the stone. There are a couple of tools that one can use in this process such as sewing needles, chisel tools, and wood files. This carving has to be correctly done because once some parts of the stone are cast away, they cannot be reused again. Space which has been created will be used to fill silver fillings to form the piece. Air holes must be left so that when the silver is being poured the process can be achieved very first.
Carbonizing of the stone happens at this point and comes before silver is poured. Pieces of stone can be attached using pieces of rubber or clamps. Silver contents are placed in a crucible and heated at a certain temperature to melt. When silver has reached its melting state, it is then poured into the intended place, and the results should be achieved within a short time.
The surface of these products is cleaned using sand. When sand is used in the cleaning process, it removes parts that are deemed unnecessary, and this does not affect the texture of these products. The other cleaning agents are citric pickling solutions which are also useful in making the surfaces appear clean. Cleaning is also aimed at getting rid of fire traces that sometimes are acquired when the soldiering process begins.
Then polishing is done on the model that has been cleaned using sand. Polishing is aimed at making the design look even more refreshing and attractive. Water can be used, or rubber or even other recommended polishing compounds. The compound range from abrasive to non abrasive, and for every stage of polishing different compounds are used.
Here comes the completion of work. There are multiple methods that one can choose to use in the final stages. At this point, one can create unique final products and other aspiration that might come to ones mind. It is important to note that the processes of sand cleaning and polishing can take a lot of time.
Stone preparation is the first step for those involved in this process. One has to find the right size of stone that fits the description of the designs they have in mind. After the proper size has been found, it is essential the two sides are flattened and left in a smooth state. The two sides need to be perfectly flat and identical to each other.
With stones ready, sketching the designs of models that one had thought of begins. Here one ought to be keen and do the job in a quiet environment to avoid disturbances which might result in errors. Also, a lot of time needs to be put when making the sketches.
Use the necessary design tools to carve the stone. There are a couple of tools that one can use in this process such as sewing needles, chisel tools, and wood files. This carving has to be correctly done because once some parts of the stone are cast away, they cannot be reused again. Space which has been created will be used to fill silver fillings to form the piece. Air holes must be left so that when the silver is being poured the process can be achieved very first.
Carbonizing of the stone happens at this point and comes before silver is poured. Pieces of stone can be attached using pieces of rubber or clamps. Silver contents are placed in a crucible and heated at a certain temperature to melt. When silver has reached its melting state, it is then poured into the intended place, and the results should be achieved within a short time.
The surface of these products is cleaned using sand. When sand is used in the cleaning process, it removes parts that are deemed unnecessary, and this does not affect the texture of these products. The other cleaning agents are citric pickling solutions which are also useful in making the surfaces appear clean. Cleaning is also aimed at getting rid of fire traces that sometimes are acquired when the soldiering process begins.
Then polishing is done on the model that has been cleaned using sand. Polishing is aimed at making the design look even more refreshing and attractive. Water can be used, or rubber or even other recommended polishing compounds. The compound range from abrasive to non abrasive, and for every stage of polishing different compounds are used.
Here comes the completion of work. There are multiple methods that one can choose to use in the final stages. At this point, one can create unique final products and other aspiration that might come to ones mind. It is important to note that the processes of sand cleaning and polishing can take a lot of time.
About the Author:
Get a summary of the things to keep in mind when choosing a tufa casting custom jewelry NM designer and more information about an experienced designer at http://www.bojoejewelry.com now.
0 commentaires:
Enregistrer un commentaire